Cozmei Ioan
Telefon validat
Iasi Iasi
Pe site din 28.02.2016
Ultima activitate 06.04.2024
- 90 anunturi
-
Vânzătorul oferă serviciul livrare cu verificare colet și permite deschiderea coletului înainte de plata pentru acest produs.
Află cum >>LM2596 LED Driver DC-DC Step-down Adjustable CC/CV Power Supply
14 RONAtentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa LM2596 LED Driver DC-DC Step-down Adjustable CC/CV Power Supply the Module Properties: non - isolated constant current and voltage of the Module * Rectification: non - synchronous Rectification * Input voltage: 7 v - 35 v * the Output voltage: 1.25 V - 30 V * the Output current: adjustable maximum 3 a * Conversion efficiency: 92% (the highest) * Switching frequency, 150 KHZ * the Output ripple: 50 mv (Max) 20 m bandwidth * the Load Regulation: plus or minus 0.5% * Voltage Regulation: plus or minus 2.5% * Operating Temperature: - 40 to + 85 the use: * Make sure of the voltage and current of the 'you need to charge * Adjust the constant voltage potentiometer to make the output voltage same to the charge voltage * Potentiometer Adjustment Direction: Clockwise (happens), counterclockwise (decrease) * Use the multimeter in 10 a current scale to measure the output short - circuit current, and adjust the current potentiometer to make sure the output current to the expected charging current value * The charge current of transfer lamp is The default 0.1 times of The charging current (constant current value) * Connected to the 'and try to charging (for previous five steps, the module input terminal is Connected to the power source, the output load is NOT Connected to batteries). LED Constant Current Driver Use: * Make sure operating current and Max operating Voltage of the LED you need to drive. * Adjust the constant voltage potentiometer to make sure the output voltage is up to the LED Max operating voltage. * Use the multimeter in 10 a current scale to measure the output short - circuit current, and adjust the current potentiometer. To make sure the output current to the expected LED operating current. * Join the LED test (For the above three steps, the module input terminal is connected to the power source, the output load is NOT connected to the LED). The scope of application: Charging for lithium ion batteries: the when the lithium ion 'voltage is low. If use the constant voltage Charging directly. Due to pressure is too large, leading to the' damage. So from the beginning to use the constant current Charging. When Charging the to a certain, automatic switch back to the constant voltage Charging. Va rog sa vizualizati si celelalte anunturi ale mele.
-
Vânzătorul oferă serviciul livrare cu verificare colet și permite deschiderea coletului înainte de plata pentru acest produs.
Află cum >>STM32F103C8T6 ARM STM32 arduino, am si programator st link V2, STM8 STM32
25 RONAtentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa STM32F103C8T6 ARM STM32 Minimum System Development Board Module For arduino programator st link V2 STM8 STM32 la 30 lei
-
Vânzătorul oferă serviciul livrare cu verificare colet și permite deschiderea coletului înainte de plata pentru acest produs.
Află cum >>STLINK ST ST-LINK/V2 (CN) STM8 STM32 Emulator download programmer
79 RONAtentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa Product introduction ST-LINK/V2 is an online simulation can be downloaded as well as STM32 and STM8 development tools. Basic properties ST is ST-LINK/V2 sense method for the evaluation of the semiconductor, the development of STM8 series and STM32 series MCU and the design of online simulation and download as one of the development tool. STM8 series through the SWIM interface and ST-LINK/V2 connection; STM32 series through the JTAG / SWD interface and ST-LINK/V2 connection. ST-LINK/V2 through high speed PC and USB2.0 end connection. Supported software Utility v2.0 ST-LINK (and above) Version 4.2.1 STVD (and above) Version 3.2.3 STVP (and above) EWARM Revision v6.20 IAR (and above) EWSTM8 Revision v1.30 IAR (and above) RVMDK Revision v4.21 KEIL (and above) ATOLLIC TASKING Supported devices Support all STM8 Series MCU with SWIM interface Support all STM32 Series MCU with JTAG / SWD interface Va rog sa vizualizati si celelalte anunturi ale mele.
-
10 RON
Atentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa IGBT FGA25N120 igbt la 25 amperi la 1200 volti 10 lei bucata.. Igbt G10N60A la 10 amperi la 600 volti TO-220 Mosfet R6020 la 20 amperi 600 volti ... 3 lei bucata TO-220FM Mosfet 20n60c3 la 20 amperi la 600 volti ... 4 lei bucata TO-220FM
-
85 RON
Electrovalva de metal 3/4, pentru apa,aer, lichide. Caracteristici Size: approx.68*60*35mm Flow direction: unidirectional (follow the arrow on valve body) Media: water, air, natural gas, propane, butane, petroleum oil, mineral oils, diesel, low viscosity fluid, etc. (do not use with gasoline) Operation mode: N/C (normally closed) Operation type: 2-way 2-position direct lift diaphragm Pipe size: 3/4" NPSM Voltage: 12 V DC Water pressure: 0.02-0.8Mpa Operating pressure differential: 3-145 psi (0.02-1 MPa) Media Temperature:15-180 ? (-10 80 ?) Electrovalva de inox 1/2 tată tată merge la 120 grade Celsius pentru încălzire la presiune de 8 bari ultimele 2 poze la 130 lei bucata.
-
36 RON
Atentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa Subler electronic, 150 mm carbon fiber composites, digital caliper. Precizie 0,1 mm Va rog sa vizualizati si celelalte anunturi ale mele.
-
Vânzătorul oferă serviciul livrare cu verificare colet și permite deschiderea coletului înainte de plata pentru acest produs.
Află cum >>Spindle cnc 500 watti, nou, sigilat,cnc
280 RONSpindle cnc 500 watti, nou, sigilat, merge reglabil de la 0 pina la 12000 rpm tensiune 0...110 volți, cu cap mandrină ER11 cu penseta in ea de 1/8 (3.175 MM) la 280 lei. Suport pentru spindle din aluminiu la 70 lei Sursă spindle 500 watti tensiune de alimentare la 220 volți sursă reglabilă 0...110 volți pentru spindle 90 lei 13 pensete de 1; 1,5; 2; 2,5; 3; 3,5, 4; 4,5; 5; 5,5; 6; 6,5; 7. 130 lei Toate noi sigilate. Sau tot setul complet la 500 lei (spindle diametru 52 cm și suport de prindere din aluminiu)+sursă+setul complet de pensete), prețul este fix, poza 5. Se vinde și separat: Spindle cnc 500 watti cu mandrină ER11 nou sigilat cu 280 lei Suport pentru spindle din aluminiu la 70 lei Sursă spindle 500 watti la 90 lei Set 13 pensete de calitate de 1; 1,5; 2; 2,5; 3; 3,5, 4; 4,5; 5; 5,5; 6; 6,5; 7. la 130 lei, totul este nou sigilat. Pensetele se vând și separat la 19 lei bucata pentru că îmi strică setul complet. Vă mulțumesc pentru înțelegere. Spindle cnc 500 watti, nou, sigilat tot setul complet la 500 lei (spindle diametru 52 cm și suport de prindere din aluminiu)+sursă+setul complet de pensete), prețul este fix. E 25 lei drumul cu awb fan Courier cu deschidere la livrare.
-
Vânzătorul oferă serviciul livrare cu verificare colet și permite deschiderea coletului înainte de plata pentru acest produs.
Află cum >>Placa cu 8 relee pentru arduino, modul pt automatizari
60 RONAtentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa Placa cu 8 relee pentru arduino automatizari, atmega328p, atmega32, atmega2560, etc. Intrare 5 volti. Comuta 250 volti maxim 10 amperi. Placa cu 4 relee 30 lei intrare 5 volti. Modul cu 1 releu 10 lei intrare 12 volti. Va rog vizionati si celelalte anunturi ale mele. Va mul?umesc.
-
Vânzătorul oferă serviciul livrare cu verificare colet și permite deschiderea coletului înainte de plata pentru acest produs.
Află cum >>Electrovalva de metal 1/2 12 volti pină la 55 grade Celsius
69 RONElectrovalva de metal 1/2 12 volti pină la 55 grade Celsius Voltage: 12V Nominal diameter: 1/2" Water pressure: 0.02-0.8Mpa Type and rated technical parameters Type: guide (one-way) solenoid valve Rated voltage: 12V Rated current: 12v-300mA Working mode: short-time quota system (intermittent duty cycle) Insulation grade: E Use of fluid: (0-55 ° C) water Use water pressure: 0.02-0.8Mpa
-
2 RON
Atentie, am foarte multe produse, module, shield-uri, pentru proiecte, licente, decat cele afisate, va rog sa-mi solicitati lista completa Rulment 624zz, interiorul de 4 mm, exteriorul de13 mm grosime de 5 mm Va rog sa vizualizati si celelalte anunturi ale mele.
-