Modul releu timp timer programabil multifunctional

Specificații

Descriere

Tensiune de alimentare: 5V;
Precizia cronometrajului: de la 0.1 secunde pana la 999 minute;
Semnal de declansare: 5V;
Sarcina de iesire la DC 14V: maxim 20A;
Sarcina de iesire la 125V AC: maxim 20A;
Curent in repaus: 20mA;
Curent in lucru: 60mA;
Greutatea produsului: 27g;
Dimensiuni: 65x34.3x17.5 mm

DC+: introduceti polul pozitiv al sursei de alimentare DC
DC-: introduceti polul negativ al sursei de alimentare DC
IN+: intrare semnal declansare pozitiv
IN-: intrare semnal declansare negativ
COM: Interfata terminala comuna

Releul are 32 de moduri de lucru dupa cum urmeaza:

P-11: Point mode, with signal suction, no signal disconnect.

P-12: self-locking mode, the relay state reverses once after each trigger.

P-13: After triggering, the relay will pull in and disconnect after A delay time; Invalid trigger during delay.

P-14: After triggering, the relay will pull in and disconnect after A delay time; Reset timer is triggered during the delay.

P-15: After triggering, the relay will pull in and disconnect after A delay time; Trigger cumulative timing during the delay.

P-16: After triggering, the relay will pull in and disconnect after A delay time; Trigger reset during delay (relay disconnects)

P-17: After triggering, the relay draws during the signal duration, the input signal disappears, and the relay is disconnected after the delay time A; During the delay period, the relay will be triggered again to keep pulling, and the timing will stop until the signal disappears at the last second time, and it will be disconnected after the delay time A.

P-18: After power-on, the relay immediately draws, and the relay is disconnected after A second delay; Until the next power on.

P-21: Give the signal, and the relay pulls in after A delay.

P-22: Give continuous signal, after A time, the relay draws; The signal is gone. The relay is disconnected.

P-23: When the signal disappears for more than A time, the relay pulls in; There is a signal. The relay is disconnected.

P-24: Give continuous signal, after A time, the relay draws; If the signal disappears for more than A time, the relay is disconnected.

P-25: Give continuous signal, after A time, the relay draws; Give the continuous signal again. After A time, the relay is disconnected

P-26: Give the signal and disconnect the relay after A time; After the signal disappears, the relay stops after drawing again for A second

P-27: There is A pulse signal (. Rising edge or falling edge). The relay is disconnected without pulse signal, and the relay pulls in after a delay time (no pulse is considered for continuous high level or continuous low level).

P-28:. After power-on, the relay will pull in after A delay until the power is off.

P-31:. After power-on, the relay absorbs A time, disconnects B time, infinite cycle; The power is off.

P-32: There is A continuous signal, the relay absorbs A time, disconnects B time, infinite cycle; The signal disappears, terminating the loop.

P-33: Give A signal, the relay absorbs A time, disconnects B time, infinite cycle; Give another signal to terminate the loop.

P-34: After power-on, the relay will be switched on after A delay and disconnected after B delay.

P-35: Give A signal, after a time delay, the relay will pull off, and after B time disconnect.

P-36: give continuous signal, after A time, the relay will pull in, and disconnect after B time; Signal lost, timing reset, relay disconnected.

P-37: If there is A signal, the relay will disconnect automatically after closing time A, and then time time B after disconnecting. The signal trigger is invalid within time A+ B.

P-38: If there is A signal, the relay will disconnect automatically after closing time A, and then time time B after disconnecting, and disconnect automatically after closing time A again.

P-41: No action if signal is present; Signal loss trigger; The relay is disconnected after A delay time.

P-42: The signal disappears and the relay pulls in after the delay time A; After another delay time B, the relay is disconnected.

P-43: The signal disappears, and the relay pulls in after the time exceeds A; After another delay time B, the relay is disconnected.

P-44:. After power-on, the relay will close A time and disconnect B time; Relay disconnects and stops after C cycles.

P-45: does not perform any operation after power-on. After the signal is given, the relay absorbs A time and disconnects B time; Relay disconnects and stops after C cycles; If the signal is given, it is executed again.

P-46: After giving the signal for more than A times, the relay draws; Maintain suction; The power is off.

P-47: After giving the signal for more than A times, the relay will pull in; Disconnect after suction B time.

P-48: After giving signals for more than A consecutive time within time C, the relay will disconnect and stop after sucking time B.

Publi24_1704309218